· This chart relates horse power to the flow rate in gallons per minute and pounds per hour In this case we need a demineralizer or softener rated for a maximum flow rate of 28 gpm It will be less depending upon how much condensate is returned

Read MoreSpecifically AFUE is the ratio of annual heat output of the furnace or compared to the total annual fossil fuel energy consumed by a furnace or An AFUE of 90% means that 90% of the energy in the fuel becomes heat for the home and the other 10% escapes up the chimney and elsewhere

Read Moreload - The horsepower lbs of steam per hour or BTU is the rating indicating the maximum of a When a operates at its maximum rated it is referred to as maximum load If the load varies from hour to hour it operates at a varying loadLoad and load variations can influence the amount of chemicals required for treatment and the treatment controls required

Read More5000000 Btu/h input (1464 kW) 5000 pounds steam per hour (06299 kg/s) capacity 1000 square foot (929 m 2) heating surface Power boilers that do not exceed one of the following limits: 5000000 Btu/h input (1464 kW) 5000 pounds steam per hour (06299 kg/s) capacity 1000 square foot

Read MoreThe from and at rating is widely used as a datum by shell manufacturers to give a a rating which shows the amount of steam in kg/h which the can create from and at 100°Cat atmospheric pressure Each kilogram of steam would then have received 2 257 kJ of heat from the

Read MoreW = (Btu/h kW) h g = enthalpy steam (Btu/lb kJ/kg) h f = enthalpy condensate (Btu/lb kJ/kg) m = steam evaporated (lb/h kg/s) Horsepower - BHP The Horsepower (BHP) is the amount of energy required to produce 345 pounds of steam per hour at a pressure and temperature of 0 Psig and 212 o F with feedwater at 0

Read MoreIf the boiler will not satisfy the code clearance requirements (minimum of 30 in front at rear and on both sides and 72 overhead) do the following: Submit three sets of plans for the installation drawn on paper that is not less than 18 x 24 in size and to a scale of not less than ¼ = 1

Read Moredescribes the heat output of a in energy units not the physical of the Manufacturers measure output in British thermal units (BTUs) per hour or horsepower (BHP) BHP measurements usually only apply to very powerful and large since one BHP equals 33475 BTUs per hour

Read MoreCan I place a 4000000 btu/h input atmospheric low pressure steam in the room without adding combustion air? The required volume is 50 ft 3 per 1000 btu/hr We take 4000000/1000 which leaves us with 4000 We multiply 4000 x 50 to get our volume of 200000 ft 3 Our building is 200000 ft 3 so we meet the

Read MoreSpecifically AFUE is the ratio of annual heat output of the furnace or compared to the total annual fossil fuel energy consumed by a furnace or An AFUE of 90% means that 90% of the energy in the fuel becomes heat for the home and the other 10% escapes up the chimney and elsewhere

Read More· Boiler has high quality construction as they are designed with the same high-quality components found in the models for commercial applications Cons: Only floor-mounted models are available Minimum capacity available is 80 MBH which might not

Read More· Without adequate air supply sizing boiler room equipment can become inefficient and cause accidents How much? The boiler room inlet air supply must be sized in accordance with the amount of air the equipment in the boiler room requires Each inlet supply opening shall have a minimum free area of 1 in 2 per 2000 Btu/h The NFPA recommends that a boiler room have at least two

Read MoreThe for a gravity-type hot water system expansion tank shall be in accordance with Table 10044(1) The for a forced-type hot water system expansion tank shall be in accordance with Table 10044(2) or Equation 10044 Equation 10044 shall not be used for diaphragm-type expansion tanks

Read MoreSERIES 28A INSTALLATION AND OPERATION INSTRUCTIONS Figure 1- Service Clearances to Adjacent Construction WARNING: Never install a 28A on top of combustible flooring without consulting the local building authorities for proper installation guidelines! A clearance of 6 in 015 m must be maintained between the

Read More1 horsepower () = 334456 Btu (mean)/hr = 1406716 calorie/min (thermo) = 1404694 calorie (mean)/min = 1407423 calorie (20oC)/min 98095x1010 erg/sec = 434107 foot-pound-force/min = 131548 horsepower (mech) = 131495 horsepower (electric) = 133372 horsepower (metric) = 131487 horsepower (water) = 98095 joule/sec = 98095 kilowatt Horsepower (hp) can be converted into lbs of

Read MoreLike heat-only boilers it is not necessary to install a boiler with a capacity greater than 18kW for the majority of properties but you must factor in the hot water requirements of your cylinder Whilst your property might only need 6-8kW of heating it may still require a bigger output for hot water

Read MoreThis means the needed to deliver the appropriate amount of BTUs to satisfy demand will be 1 inch pipe steel or copper Delta T Piping Flow & Pipe Sizing - It is very important this is correctly done as too much flow rate reduces efficiency as described above and it can have detrimental effects on the

Read MoreFor cast iron the valve shall be determined by the maximum output method In every case the safety valve for each steam shall be such that with the fuel burning equipment installed and operated at maximum the pressure cannot rise more than 5psig (35 kilopascals) above the MAWP

Read MoreThis means the needed to deliver the appropriate amount of BTUs to satisfy demand will be 1 inch pipe steel or copper Delta T Piping Flow & Pipe Sizing - It is very important this is correctly done as too much flow rate reduces efficiency as described above and it can have detrimental effects on the

Read MoreRemember that one BHP equals 33475 British thermal units Therefore dividing this by 1000 this general rule requires 33475 BTUs of power output per square foot Take caution not to purchase a boiler based on this general rule as numerous factors

Read MoreOne horsepower = 345 lbs/hr of steam (or water) from and at 212o F We also know that one-gallon of water weighs 837 lbs To calculate the storage tank needed use the following formula: BHP X 345 ÷ 8337 lbs ÷ 60 min X 10 = useable in gallons For example if you have a 500 HP the calculation will be as

Read MoreThe State's minimum requirements for boilers/water heaters and pressure vessels over 200000 BTU/h (5861 kW) 210 degrees Fahrenheit or 120 gallons capacity shall be established by OCGA Title 25 Chapter 15 and the Rules and Regulations of the Office of Insurance and Safety Fire Commissioner (Effective January 1 2014)

Read MoreClick now! Start your project today!